Description Silver Zinc is a fast drying epoxy based metallic zinc coating which provides excellent adhesion, corrosion resistance and long lasting durability to metal surfaces. It can be used as an anti-corrosive primer and top coat in a onestep application. It can also be used as a touch up coating for welded areas on galvanised products however for longer term protection and highly corrosive conditions Grey Zinc is recommended before the application of Silver Zinc as a finish coat.
FEATURES
Fast drying Metallic Silver Finish Excellent Adhesion Corrosion Resistant Long lasting durability Protect-Match-Seal Industrial strength
APPLICATIONS It can be used as an anti-corrosive primer and top coat in a onestep application. It can also be used as a touch up coating for welded areas on galvanised products however for longer term protection and highly corrosive conditions Grey Zinc is recommended before the application of Silver Zinc as a finish coat.
Suitable Surfaces: Steel, wrought iron, galvanised iron and non-ferrous metals such as; aluminium, alloys, ZINCALUME® and stainless steel with appropriate primer.
TYPICAL PROPERTIES OF SILVER ZINC (Note:Data is typical and does not constitute a specification.) Physical State   Liquid Colour   Silver Finish   Metallic Odor   Solvent odour Solubility in water   Not miscible with Water Size   400g Aerosol Propellant   Dimethyl Ether Flash Point (°C)   -41 (propellant) Flammability   HIGHLY FLAMMABLE.
INSTRUCTIONS
SUITABLE SURFACE Steel, wrought iron, galvanised iron and non-ferrous metals such as; aluminium, alloys, ZINCALUME® and stainless steel with appropriate primer.
IDEAL APPLICATION TEMPERATURE Between 10°C and 40°C. Avoid use in windy conditions.
PREPARATION Surface should be clean, dry and free from contaminants such as rust, oil, grease, dirt and salt. Welds should be ground back to clean white metal. Thoroughly sand new metal and lightly sand previously painted surfaces to ensure maximum adhesion. Remove loose rust and flaking paint with a wire brush, scraper or mechanical sander. For best results, always remove rust back to bare metal. For superior protection and adhesion on mild steel surfaces and welds it is recommended to prime with Grey Zinc and allowing it to dry for 4-6 hours before applying 2 coats of Silver Zinc. For non-ferrous metals such as aluminium, alloys, ZINCALUME® and stainless steel use Grey Zinc.
APPLICATION Surface should be clean, dry and free from contaminants such as rust, oil, grease, dirt and salt. Welds should be ground back to clean white metal. Thoroughly sand new metal and lightly sand previously painted surfaces to ensure maximum adhesion. Remove loose rust and flaking paint with a wire brush, scraper or mechanical sander. For best results, always remove rust back to bare metal. For superior protection and adhesion on mild steel surfaces and welds it is recommended to prime with Grey Zinc and allowing it to dry for 4-6 hours before applying 2 coats of Silver Zinc. For non-ferrous metals such as aluminium, alloys, ZINCALUME® and stainless steel use Grey Zinc.
COVERAGE Approximately 2m2 per can (depending on the surface and amount of overspray).
DRYING TIME Touch dry in 20 minutes (25°C). recoat after 1 hour. Hard dry in 16-24 hours. Drying will be slower in cold and humid conditions, in the absence of ventilation or where heavy film build is applied.
AFTER SPRAYING Prevent blocking by holding the can upside down and spraying until only clear gas escapes. Also wipe pray tip of nozzle clean. Clean up wet paint with mineral turpentine, xylene or general purpose thinner.
STORAGE Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F. Store in well-ventilated place.
DISPOSAL Dispose of contents/container according to regional regulations.
Alternative SKU: A101 Part Number/SKU: A101
* Product Images are for illustration purposes only, unless otherwise specified colour may be different.
ADDITIONAL INFORMATION
Price
$7.90
Location
Australia
Condition
New
Delivers To
Australia Wide
YOU MAY ALSO LIKE
11
Tennant T5 Sweeper Sweeping/Cleaning
TENNANT T5 SCRUBBERONLY 565 GENUINE HOURS REGULARLY MAINTAINEDBRAND NEW BATTERIES WORTH OVER $2000ONE...
$7,645.00(Drive Away)
1 week ago
Austral
,
NSW
Used
3
Comidisc Mini Polifan 50mm CDR A 60g Aluminium Oxide Pferd 47202528
47202528Â COMBIDISC MINI POLIFAN - ALUMINIUM OXIDE - TYPE CDR-PFF 50 A 60 (Each) For general-purpose coarse grinding...
You can check your conversation between the seller and you in
My Messages. Keep yourself safe. Always meet in person and never send or wire money.
Click here to learn more.